Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.2.1-RC #0: Sun Feb  1 00:48:20 CET 2004
    root@nudel.salatschuessel.net:/usr/obj/i386-5.2/usr/src/sys/NUDEL
Preloaded elf kernel "/boot/kernel/kernel" at 0xc087d000.
MPTable: <ECS      P6LX2-A     >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Pentium II/Pentium II Xeon/Celeron (334.09-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x652  Stepping = 2
  Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory  = 268435456 (256 MB)
avail memory = 250994688 (239 MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ioapic0: Assuming intbase of 0
ioapic0 <Version 1.1> irqs 0-23 on motherboard
Pentium Pro MTRR support enabled
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcibios: BIOS version 2.10
Using $PIR table, 8 entries at 0xc00fdd70
pcib0: <MPTable Host-PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pcib0: unable to route slot 7 INTD
pcib0: slot 9 INTA routed to irq 16
pcib0: slot 11 INTA routed to irq 18
pcib0: slot 12 INTA routed to irq 19
pcib0: slot 13 INTA routed to irq 16
pcib0: slot 13 INTB routed to irq 17
agp0: <Intel 82443LX (440 LX) host to PCI bridge> mem 0xe0000000-0xe03fffff at device 0.0 on pci0
pcib1: <MPTable PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pcib1: slot 0 INTA routed to irq 16
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port 0xf000-0xf00f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
pci0: <serial bus, USB> at device 7.2 (no driver attached)
intpm0: <Intel 82371AB Power management controller> port 0x5000-0x500f irq 9 at device 7.3 on pci0
intpm0: I/O mapped 5000
intpm0: intr IRQ 9 enabled revision 0
intsmb0: <Intel PIIX4 SMBUS Interface> on intpm0
smbus0: <System Management Bus> on intsmb0
smb0: <SMBus generic I/O> on smbus0
intpm0: PM I/O mapped 6100 
atapci1: <SiI 0680 UDMA133 controller> port 0x7800-0x780f,0x7400-0x7403,0x7000-0x7007,0x6c00-0x6c03,0x6800-0x6807 mem 0xe0400000-0xe04000ff irq 16 at device 9.0 on pci0
atapci1: [MPSAFE]
ata2: at 0xe0400000 on atapci1
ata2: [MPSAFE]
ata3: at 0xe0400000 on atapci1
ata3: [MPSAFE]
pci0: <network, ethernet> at device 11.0 (no driver attached)
ahc0: <Adaptec 2940 Ultra2 SCSI adapter (OEM)> port 0x8000-0x80ff mem 0xe0402000-0xe0402fff irq 19 at device 12.0 on pci0
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
sym0: <885> port 0x8400-0x84ff mem 0xe0404000-0xe0404fff,0xe0403000-0xe04030ff irq 16 at device 13.0 on pci0
sym0: Symbios NVRAM, ID 7, Fast-20, SE, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: PCI BUS clock seems too high: 40401 KHz.
pci0: <network, ethernet> at device 13.1 (no driver attached)
orm0: <Option ROMs> at iomem 0xd8000-0xdb7ff,0xd2000-0xd77ff,0xd1000-0xd17ff,0xc8000-0xc9fff,0xc0000-0xc7fff on isa0
pmtimer0 on isa0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 irq 1 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
unknown: <PNP0c02> can't assign resources (memory)
unknown: <PNP0a03> can't assign resources (port)
sio0: <16550A-compatible COM port> at port 0x3f8-0x3ff irq 4 on isa0
sio0: type 16550A
unknown: <PNP0700> can't assign resources (port)
ppc0: <Standard parallel printer port> at port 0x3bc-0x3bf irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
sio1: <16550A-compatible COM port> at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
Timecounters tick every 10.000 msec
GEOM: create disk ad0 dp=0xc2d67660
ad0: 19092MB <ST320413A> [38792/16/63] at ata0-master UDMA33
acd0: DVDROM <_NEC DV-5700A> at ata1-slave PIO4
GEOM: create disk ad5 dp=0xc2d67260
ad5: 152627MB <SAMSUNG SP1604N> [310101/16/63] at ata2-slave UDMA100
GEOM: create disk ad6 dp=0xc2ddfc60
ad6: 19470MB <QUANTUM FIREBALLlct10 20> [39560/16/63] at ata3-master UDMA66
Waiting 2 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
sa0 at ahc0 bus 0 target 5 lun 0
sa0: <HP C1533A A708> Removable Sequential Access SCSI-2 device 
sa0: 10.000MB/s transfers (10.000MHz, offset 32)
sa1 at ahc0 bus 0 target 6 lun 0
sa1: <HP C1537A L812> Removable Sequential Access SCSI-2 device 
sa1: 10.000MB/s transfers (10.000MHz, offset 32)
GEOM: create disk cd0 dp=0xc2dc5600
GEOM: create disk cd1 dp=0xc2dc4e00
GEOM: create disk cd2 dp=0xc2dc4600
GEOM: create disk da0 dp=0xc2df3450
GEOM: create disk da1 dp=0xc2dea050
GEOM: create disk da2 dp=0xc2deb050
GEOM: create disk da3 dp=0xc2df6450
GEOM: create disk da4 dp=0xc2df4050
GEOM: create disk da5 dp=0xc2dfa450
GEOM: create disk da6 dp=0xc2df5850
GEOM: create disk da7 dp=0xc2df4c50
da1 at sym0 bus 0 target 0 lun 0
da1: <SEAGATE ST11200N SUN1.05 9500> Fixed Direct Access SCSI-2 device 
da1: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da1: 1005MB (2059140 512 byte sectors: 64H 32S/T 1005C)
da2 at sym0 bus 0 target 1 lun 0
da2: <SEAGATE ST31200N 8590> Fixed Direct Access SCSI-2 device 
da2: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da2: 1006MB (2061108 512 byte sectors: 64H 32S/T 1006C)
da3 at sym0 bus 0 target 2 lun 0
da3: <SEAGATE ST31200N 8590> Fixed Direct Access SCSI-2 device 
da3: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da3: 1006MB (2061108 512 byte sectors: 64H 32S/T 1006C)
da4 at sym0 bus 0 target 3 lun 0
da4: <SEAGATE ST31200N 8590> Fixed Direct Access SCSI-2 device 
da4: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da4: 1006MB (2061108 512 byte sectors: 64H 32S/T 1006C)
da6 at sym0 bus 0 target 5 lun 0
da6: <Quantum VP32210 81HA> Fixed Direct Access SCSI-2 device 
da6: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da6: 2103MB (4308352 512 byte sectors: 255H 63S/T 268C)
da5 at sym0 bus 0 target 4 lun 0
da5: <SEAGATE ST31200N 8590> Fixed Direct Access SCSI-2 device 
da5: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da5: 1006MB (2061108 512 byte sectors: 64H 32S/T 1006C)
da7 at sym0 bus 0 target 6 lun 0
da7: <NEC DSE2100S 0307> Fixed Direct Access SCSI-2 device 
da7: 10.000MB/s transfers (10.000MHz, offset 15)
da7: 2014MB (4124736 512 byte sectors: 255H 63S/T 256C)
cd2 at ata1 bus 0 target 1 lun 0
cd2: <_NEC DV-5700A 1.30> Removable CD-ROM SCSI-0 device 
cd2: 16.000MB/s transfers
cd2: Attempt to query device size failed: NOT READY, Medium not present
cd0 at ahc0 bus 0 target 3 lun 0
cd0: <SANYO CRD-254S 1.02> Removable CD-ROM SCSI-2 device 
cd0: 3.300MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
da0 at ahc0 bus 0 target 8 lun 0
da0: <SEAGATE ST34573W 6244> Fixed Direct Access SCSI-2 device 
da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da0: 4340MB (8888924 512 byte sectors: 255H 63S/T 553C)
SMP: AP CPU #1 Launched!
cd1 at ahc0 bus 0 target 4 lun 0
cd1: <YAMAHA CRW4416S 1.0j> Removable CD-ROM SCSI-2 device 
cd1: 8.333MB/s transfers (8.333MHz, offset 31)
cd1: Attempt to query device size failed: NOT READY, Medium not present - tray closed
Mounting root from ufs:/dev/ad0s1a
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0x7c00-0x7c7f mem 0xe0401000-0xe040107f irq 18 at device 11.0 on pci0
xl0: Ethernet address: 00:01:02:b4:de:2f
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto