Copyright (c) 1992-2002 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.0-DP2 #1: Mon Nov 25 22:41:52 CET 2002 root@stardust.terra.ger:/usr/obj/usr/src/sys/GENERIC2 Preloaded elf kernel "/boot/kernel/kernel" at 0xc0692000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc06920b4. Calibrating clock(s) ... TSC clock: 935444634 Hz, i8254 clock: 1193169 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz CLK_USE_TSC_CALIBRATION not specified - using old calibration method CPU: Pentium III/Pentium III Xeon/Celeron (935.46-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x68a Stepping = 10 Features=0x387fbff real memory = 1610547200 (1535 MB) Physical memory chunk(s): 0x00001000 - 0x0009efff, 647168 bytes (158 pages) 0x006bc000 - 0x5ffe7fff, 1603452928 bytes (391468 pages) avail memory = 1559879680 (1487 MB) Programming 24 pins in IOAPIC #0 IOAPIC #0 intpin 2 -> irq 0 FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000 cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000 io0 (APIC): apic id: 2, version: 0x00178011, at 0xfec00000 bios32: Found BIOS32 Service Directory header at 0xc00fae20 bios32: Entry = 0xfb290 (c00fb290) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xf0000+0xb2c0 pnpbios: Found PnP BIOS data at 0xc00fbcc0 pnpbios: Entry = f0000:bcf0 Rev = 1.0 Other BIOS signatures found: Initializing GEOMetry subsystem random: mem: Pentium Pro MTRR support enabled null: SMP: CPU0 bsp_apic_configure(): lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000010 SVR: 0x000001ff npx0: on motherboard npx0: INT 16 interface acpi0: on motherboard pci_open(1): mode 1 addr port (0x0cf8) is 0x80000060 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=06911106) Using $PIR table, 9 entries at 0xc00fdc40 PCI-Only Interrupts: 5 9 10 11 Location Bus Device Pin Link IRQs slot 1 0 18 A 0x02 3 4 5 7 9 10 11 12 14 15 slot 1 0 18 B 0x03 3 4 5 7 9 10 11 12 14 15 slot 1 0 18 C 0x05 3 4 5 7 9 10 11 12 14 15 slot 1 0 18 D 0x01 3 4 5 7 9 10 11 12 14 15 slot 2 0 14 A 0x01 3 4 5 7 9 10 11 12 14 15 slot 2 0 14 B 0x02 3 4 5 7 9 10 11 12 14 15 slot 2 0 14 C 0x03 3 4 5 7 9 10 11 12 14 15 slot 2 0 14 D 0x05 3 4 5 7 9 10 11 12 14 15 slot 3 0 15 A 0x02 3 4 5 7 9 10 11 12 14 15 slot 3 0 15 B 0x03 3 4 5 7 9 10 11 12 14 15 slot 3 0 15 C 0x05 3 4 5 7 9 10 11 12 14 15 slot 3 0 15 D 0x01 3 4 5 7 9 10 11 12 14 15 slot 4 0 16 A 0x03 3 4 5 7 9 10 11 12 14 15 slot 4 0 16 B 0x05 3 4 5 7 9 10 11 12 14 15 slot 4 0 16 C 0x01 3 4 5 7 9 10 11 12 14 15 slot 4 0 16 D 0x02 3 4 5 7 9 10 11 12 14 15 slot 5 0 17 A 0x05 3 4 5 7 9 10 11 12 14 15 slot 5 0 17 B 0x01 3 4 5 7 9 10 11 12 14 15 slot 5 0 17 C 0x02 3 4 5 7 9 10 11 12 14 15 slot 5 0 17 D 0x03 3 4 5 7 9 10 11 12 14 15 slot 6 0 12 A 0x03 3 4 5 7 9 10 11 12 14 15 slot 6 0 12 B 0x05 3 4 5 7 9 10 11 12 14 15 slot 6 0 12 C 0x01 3 4 5 7 9 10 11 12 14 15 slot 6 0 12 D 0x02 3 4 5 7 9 10 11 12 14 15 slot 7 0 13 A 0x05 3 4 5 7 9 10 11 12 14 15 slot 7 0 13 B 0x01 3 4 5 7 9 10 11 12 14 15 slot 7 0 13 C 0x02 3 4 5 7 9 10 11 12 14 15 slot 7 0 13 D 0x03 3 4 5 7 9 10 11 12 14 15 embedded 0 1 A 0x01 3 4 5 7 9 10 11 12 14 15 embedded 0 1 B 0x02 3 4 5 7 9 10 11 12 14 15 embedded 0 1 C 0x03 3 4 5 7 9 10 11 12 14 15 embedded 0 1 D 0x05 3 4 5 7 9 10 11 12 14 15 embedded 0 7 C 0x03 3 4 5 7 9 10 11 12 14 15 embedded 0 7 D 0x05 3 4 5 7 9 10 11 12 14 15 acpi0: power button is handled as a fixed feature programming model. ACPI timer looks GOOD min = 1, max = 2, width = 2 ACPI timer looks GOOD min = 1, max = 2, width = 2 ACPI timer looks BAD min = 1, max = 5, width = 5 ACPI timer looks BAD min = 1, max = 5, width = 5 ACPI timer looks BAD min = 1, max = 6, width = 6 ACPI timer looks BAD min = 1, max = 6, width = 6 ACPI timer looks BAD min = 1, max = 5, width = 5 ACPI timer looks BAD min = 1, max = 6, width = 6 ACPI timer looks BAD min = 1, max = 5, width = 5 ACPI timer looks BAD min = 1, max = 6, width = 6 Timecounter "ACPI-safe" frequency 3579545 Hz acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0 acpi_cpu0: on acpi0 acpi_cpu1: on acpi0 acpi_button0: on acpi0 acpi_button1: on acpi0 pcib0: port 0x6000-0x607f,0x5000-0x500f,0x4080-0x40ff,0x4000-0x407f,0xcf8-0xcff on acpi0 ---- initial configuration ------------------------ \\_SB_.PCI0.LNKA irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.0 \\_SB_.PCI0.LNKB irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.1 \\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.2 \\_SB_.PCI0.LNKD irq 9: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.3 ---- before setting priority for links ------------ ---- before fixup boot-disabled links ------------- ---- after fixup boot-disabled links -------------- ---- arbitrated configuration --------------------- \\_SB_.PCI0.LNKA irq 5: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.0 \\_SB_.PCI0.LNKB irq 11: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.1 \\_SB_.PCI0.LNKC irq 10: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.2 \\_SB_.PCI0.LNKD irq 9: [ 1 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.3 pci0: on pcib0 pci0: physical bus=0 map[10]: type 3, range 32, base d0000000, size 26, enabled found-> vendor=0x1106, dev=0x0691, revid=0xc4 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x2210, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D3 current D0 found-> vendor=0x1106, dev=0x8598, revid=0x00 bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0007, statreg=0x2230, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns) found-> vendor=0x1106, dev=0x0686, revid=0x40 bus=0, slot=7, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x0087, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D3 current D0 map[20]: type 4, range 32, base 0000a000, size 4, enabled found-> vendor=0x1106, dev=0x0571, revid=0x06 bus=0, slot=7, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D3 current D0 IOAPIC #0 intpin 19 -> irq 2 Freeing (NOT implemented) redirected PCI irq 9. map[20]: type 4, range 32, base 0000a400, size 5, enabled found-> vendor=0x1106, dev=0x3038, revid=0x16 bus=0, slot=7, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=2 powerspec 2 supports D0 D3 current D0 Freeing (NOT implemented) redirected PCI irq 9. map[20]: type 4, range 32, base 0000a800, size 5, enabled found-> vendor=0x1106, dev=0x3038, revid=0x16 bus=0, slot=7, func=3 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=2 powerspec 2 supports D0 D3 current D0 found-> vendor=0x1106, dev=0x3057, revid=0x40 bus=0, slot=7, func=4 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0000, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D3 current D0 IOAPIC #0 intpin 18 -> irq 5 Freeing (NOT implemented) redirected PCI irq 10. map[10]: type 4, range 32, base 0000ac00, size 8, enabled map[14]: type 4, range 32, base 0000b000, size 2, enabled map[18]: type 4, range 32, base 0000b400, size 2, enabled found-> vendor=0x1106, dev=0x3058, revid=0x50 bus=0, slot=7, func=5 class=04-01-00, hdrtype=0x00, mfdev=0 cmdreg=0x0001, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=5 powerspec 2 supports D0 D3 current D0 Freeing (NOT implemented) redirected PCI irq 10. map[10]: type 4, range 32, base 0000b800, size 3, enabled map[14]: type 4, range 32, base 0000bc00, size 2, enabled map[18]: type 4, range 32, base 0000c000, size 3, enabled map[1c]: type 4, range 32, base 0000c400, size 2, enabled map[20]: type 4, range 32, base 0000c800, size 6, enabled map[24]: type 1, range 32, base db000000, size 17, enabled found-> vendor=0x105a, dev=0x0d30, revid=0x02 bus=0, slot=12, func=0 class=01-04-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=5 powerspec 1 supports D0 D3 current D0 Freeing (NOT implemented) redirected PCI irq 9. map[10]: type 1, range 32, base db024000, size 11, enabled map[14]: type 1, range 32, base db020000, size 14, enabled found-> vendor=0x104c, dev=0x8020, revid=0x00 bus=0, slot=13, func=0 class=0c-00-10, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x04 (1000 ns) intpin=a, irq=2 powerspec 1 supports D0 D2 D3 current D0 IOAPIC #0 intpin 16 -> irq 9 Freeing (NOT implemented) redirected PCI irq 5. map[10]: type 4, range 32, base 0000cc00, size 8, enabled map[14]: type 1, range 32, base db025000, size 8, enabled found-> vendor=0x1106, dev=0x3065, revid=0x43 bus=0, slot=14, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x08 (2000 ns) intpin=a, irq=9 powerspec 2 supports D0 D3 current D0 IOAPIC #0 intpin 17 -> irq 10 Freeing (NOT implemented) redirected PCI irq 11. map[10]: type 4, range 32, base 0000d000, size 3, enabled map[14]: type 4, range 32, base 0000d400, size 3, enabled map[18]: type 4, range 32, base 0000d800, size 3, enabled map[1c]: type 4, range 32, base 0000dc00, size 3, enabled map[20]: type 4, range 32, base 0000e000, size 3, enabled map[24]: type 4, range 32, base 0000e400, size 4, enabled found-> vendor=0x9710, dev=0x9815, revid=0x01 bus=0, slot=15, func=0 class=07-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0003, statreg=0x0280, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 Freeing (NOT implemented) redirected PCI irq 10. map[10]: type 4, range 32, base 0000e800, size 8, enabled map[14]: type 1, range 32, base db026000, size 8, enabled found-> vendor=0x10cd, dev=0x1300, revid=0x03 bus=0, slot=16, func=0 class=01-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0280, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x04 (1000 ns), maxlat=0x04 (1000 ns) intpin=a, irq=5 Freeing (NOT implemented) redirected PCI irq 11. map[10]: type 4, range 32, base 0000ec00, size 8, enabled map[14]: type 1, range 32, base db027000, size 8, enabled map[18]: type 1, range 32, base db028000, size 12, enabled found-> vendor=0x1000, dev=0x000f, revid=0x26 bus=0, slot=18, func=0 class=01-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x86 (4020 ns), mingnt=0x11 (4250 ns), maxlat=0x40 (16000 ns) intpin=a, irq=10 powerspec 1 supports D0 D3 current D0 agp0: mem 0xd0000000-0xd3ffffff at device 0.0 on pci0 agp0: allocating GATT for aperture of size 256M pcib1: at device 1.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0x9000-0x9fff pcib1: memory decode 0xd8000000-0xd9ffffff pcib1: prefetched decode 0xd4000000-0xd7ffffff pci1: on pcib1 pci1: physical bus=1 Freeing (NOT implemented) redirected PCI irq 5. map[10]: type 3, range 32, base d4000000, size 26, enabled map[14]: type 4, range 32, base 00009000, size 8, enabled map[18]: type 1, range 32, base d9000000, size 14, enabled found-> vendor=0x1002, dev=0x524c, revid=0x00 bus=1, slot=0, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0087, statreg=0x02b0, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) intpin=a, irq=9 powerspec 1 supports D0 D1 D3 current D0 pci1: at device 0.0 (no driver attached) isab0: at device 7.0 on pci0 isa0: on isab0 atapci0: port 0xa000-0xa00f at device 7.1 on pci0 ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xa000 ata0: mask=03 ostat0=50 ostat2=00 ata0-master: ATAPI 00 00 ata0-slave: ATAPI 00 00 ata0: mask=03 stat0=50 stat1=00 ata0-master: ATA 01 a5 ata0: devices=01 ata0: at 0x1f0 irq 14 on atapci0 ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xa008 ata1: mask=03 ostat0=50 ostat2=00 ata1-master: ATAPI 00 00 ata1-slave: ATAPI 00 00 ata1: mask=03 stat0=50 stat1=00 ata1-master: ATA 01 a5 ata1: devices=01 ata1: at 0x170 irq 15 on atapci0 uhci0: port 0xa400-0xa41f irq 2 at device 7.2 on pci0 usb0: on uhci0 usb0: USB revision 1.0 uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: port 0xa800-0xa81f irq 2 at device 7.3 on pci0 usb1: on uhci1 usb1: USB revision 1.0 uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered pci0: at device 7.5 (no driver attached) atapci1: port 0xc800-0xc83f,0xc400-0xc403,0xc000-0xc007,0xbc00-0xbc03,0xb800-0xb807 mem 0xdb000000-0xdb01ffff irq 5 at device 12.0 on pci0 ata2: iobase=0xb800 altiobase=0xbc02 bmaddr=0xc800 ata2: mask=03 ostat0=00 ostat2=00 ata2-master: ATAPI 00 00 ata2-slave: ATAPI 00 00 ata2: mask=03 stat0=00 stat1=00 ata2: devices=00 ata2: at 0xb800 on atapci1 ata3: iobase=0xc000 altiobase=0xc402 bmaddr=0xc808 ata3: mask=03 ostat0=00 ostat2=00 ata3-master: ATAPI 14 eb ata3-slave: ATAPI 10 10 ata3: mask=03 stat0=00 stat1=00 ata3: devices=04 ata3: at 0xc000 on atapci1 pci0: at device 13.0 (no driver attached) vr0: port 0xcc00-0xccff mem 0xdb025000-0xdb0250ff irq 9 at device 14.0 on pci0 vr0: Ethernet address: 00:50:ba:21:d7:c7 miibus0: on vr0 ukphy0: on miibus0 ukphy0: OUI 0x000580, model 0x0000, rev. 0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto vr0: bpf attached pci0: at device 15.0 (no driver attached) adv0: port 0xe800-0xe8ff mem 0xdb026000-0xdb0260ff irq 5 at device 16.0 on pci0 adv0: Warning EEPROM Checksum mismatch. Using default device parameters adv0: AdvanSys SCSI Host Adapter, SCSI ID 7, queue depth 16 sym0: <875> port 0xec00-0xecff mem 0xdb028000-0xdb028fff,0xdb027000-0xdb0270ff irq 10 at device 18.0 on pci0 sym0: No NVRAM, ID 7, Fast-20, SE, parity checking sym0: open drain IRQ line driver, using on-chip SRAM sym0: using LOAD/STORE-based firmware. fdc0: port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 sio0: irq maps: 0x1 0x11 0x1 0x1 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A unknown: not probed (disabled) sio1: irq maps: 0x1 0x9 0x1 0x1 sio1 port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A unknown: not probed (disabled) ppc0: using extended I/O port range ppc0: ECP SPP ECP+EPP SPP ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold plip0: on ppbus0 lp0: bpf attached lpt0: on ppbus0 lpt0: Interrupt-driven port ppi0: on ppbus0 psmcpnp0 irq 12 on acpi0 atkbdc0: port 0x64,0x60 irq 1 on acpi0 atkbd0: flags 0x1 irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0047 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000 psm0: current command byte:0047 psm0: irq 12 on atkbdc0 psm0: model Generic PS/2 mouse, device ID 0-00, 3 buttons psm0: config:00000000, flags:00000000, packet size:3 psm0: syncmask:c0, syncbits:00 unknown: not probed (disabled) unknown: not probed (disabled) adv: adv0 already exists; skipping it ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it fdc: fdc0 already exists; skipping it ppc: ppc0 already exists; skipping it sio: sio0 already exists; skipping it sio: sio1 already exists; skipping it Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 ex_isa_identify() sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: