Copyright (c) 1992-2001 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #0: Tue Jul 24 14:39:35 CEST 2001
    root@hmscrap.hcs.de:/usr/src/sys/i386/compile/SMP
Calibrating clock(s) ... TSC clock: 401168257 Hz, i8254 clock: 1193953 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254"  frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium II/Pentium II Xeon/Celeron (400.91-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x665  Stepping = 5
  Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory  = 167706624 (163776K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x003e0000 - 0x09fe7fff, 163610624 bytes (39944 pages)
avail memory = 159219712 (155488K bytes)
Programming 24 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
SMP: CPU0 apic_initialize():
     lint0: 0x00000700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): apic id:  0, version: 0x00040011, at 0xfee00000
 cpu1 (AP):  apic id:  1, version: 0x00040011, at 0xfee00000
 io0 (APIC): apic id:  2, version: 0x00170011, at 0xfec00000
bios32: Found BIOS32 Service Directory header at 0xc00faec0
bios32: Entry = 0xfb340 (c00fb340)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xb370
pnpbios: Found PnP BIOS data at 0xc00fbf10
pnpbios: Entry = f0000:bf38  Rev = 1.0
Other BIOS signatures found:
Preloaded elf kernel "kernel" at 0xc03b7000.
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
SMP: CPU0 bsp_apic_configure():
     lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000010 SVR: 0x000001ff
Using $PIR table, 7 entries at 0xc00fdc60
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443LX (440 LX) host to PCI bridge> at pcibus 0 on motherboard
pci0: physical bus=0
	map[10]: type 3, range 32, base e0000000, size 26, enabled
found->	vendor=0x8086, dev=0x7180, revid=0x03
	bus=0, slot=0, func=0
	class=06-00-00, hdrtype=0x00, mfdev=0
found->	vendor=0x8086, dev=0x7181, revid=0x03
	bus=0, slot=1, func=0
	class=06-04-00, hdrtype=0x01, mfdev=0
found->	vendor=0x8086, dev=0x7110, revid=0x01
	bus=0, slot=7, func=0
	class=06-01-00, hdrtype=0x00, mfdev=1
	map[20]: type 4, range 32, base 0000f000, size  4, enabled
found->	vendor=0x8086, dev=0x7111, revid=0x01
	bus=0, slot=7, func=1
	class=01-01-80, hdrtype=0x00, mfdev=0
	map[20]: type 4, range 32, base 0000d000, size  5, enabled
found->	vendor=0x8086, dev=0x7112, revid=0x01
	bus=0, slot=7, func=2
	class=0c-03-00, hdrtype=0x00, mfdev=0
	intpin=d, irq=255
	map[90]: type 4, range 32, base 00005000, size  4, enabled
found->	vendor=0x8086, dev=0x7113, revid=0x01
	bus=0, slot=7, func=3
	class=06-80-00, hdrtype=0x00, mfdev=0
IOAPIC #0 intpin 16 -> irq 2
Freeing (NOT implemented) redirected PCI irq 11.
	map[10]: type 4, range 32, base 0000d400, size  3, enabled
	map[14]: type 1, range 32, base e7000000, size  8, enabled
found->	vendor=0x1043, dev=0x0675, revid=0x02
	bus=0, slot=8, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	intpin=a, irq=2
	powerspec 1  supports D0 D1 D2 D3  current D0
IOAPIC #0 intpin 17 -> irq 16
Freeing (NOT implemented) redirected PCI irq 10.
	map[10]: type 1, range 32, base e7001000, size  6, enabled
	map[14]: type 4, range 32, base 0000d800, size  6, enabled
	map[18]: type 4, range 32, base 0000dc00, size  5, enabled
found->	vendor=0x1244, dev=0x0700, revid=0x01
	bus=0, slot=9, func=0
	class=02-80-00, hdrtype=0x00, mfdev=0
	intpin=a, irq=16
IOAPIC #0 intpin 19 -> irq 17
Freeing (NOT implemented) redirected PCI irq 5.
	map[10]: type 4, range 32, base 0000e000, size  8, enabled
	map[14]: type 1, range 32, base e7002000, size  8, enabled
found->	vendor=0x10ec, dev=0x8139, revid=0x10
	bus=0, slot=11, func=0
	class=02-00-00, hdrtype=0x00, mfdev=0
	intpin=a, irq=17
	powerspec 1  supports D0 D1 D2 D3  current D0
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0xc000-0xcfff
pcib1:   memory decode     0xe4000000-0xe5ffffff
pcib1:   prefetched decode 0xe6000000-0xe6ffffff
pci1: physical bus=1
Freeing (NOT implemented) redirected PCI irq 11.
	map[10]: type 1, range 32, base e4000000, size 24, enabled
	map[14]: type 3, range 32, base e6000000, size 24, enabled
found->	vendor=0x12d2, dev=0x0018, revid=0x10
	bus=1, slot=0, func=0
	class=03-00-00, hdrtype=0x00, mfdev=0
	intpin=a, irq=2
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 7.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xf000
ata0: mask=03 ostat0=50 ostat2=00
ata0-master: ATAPI probe 00 00
ata0-slave: ATAPI probe 00 00
ata0: mask=03 stat0=50 stat1=00
ata0-master: ATA probe 01 a5
ata0: devices=01
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xf008
ata1: mask=03 ostat0=51 ostat2=7f
ata1-master: ATAPI probe 14 eb
ata1-slave: ATAPI probe 7f 7f
ata1: mask=03 stat0=10 stat1=7f
ata1-slave: ATA probe 7f ff
ata1: devices=04
ata1: at 0x170 irq 15 on atapci0
pci0: <serial bus, USB> at 7.2 (no driver attached)
Timecounter "PIIX"  frequency 3579545 Hz
pci0: <bridge, PCI-unknown> at 7.3 (no driver attached)
pci0: <network> at 8.0 (no driver attached)
iavc0: <AVM B1 PCI> port 0xdc00-0xdc1f,0xd800-0xd83f mem 0xe7001000-0xe700103f irq 16 at device 9.0 on pci0
capi0: card type 2 attached
rl0: <RealTek 8139 10/100BaseTX> port 0xe000-0xe0ff mem 0xe7002000-0xe70020ff irq 17 at device 11.0 on pci0
rl0: Realtek 8139B detected. Warning, this may be unstable in autoselect mode
rl0: Ethernet address: 00:a0:d2:a5:c8:c0
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: rl0 attached
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
pnpbios: 14 devices, largest 78 bytes
PNP0200: adding dma mask 0x10
PNP0200: adding io range 0-0xf, size=0x10, align=0
PNP0200: adding io range 0x81-0x83, size=0x3, align=0
PNP0200: adding io range 0x87-0x87, size=0x1, align=0
PNP0200: adding io range 0x89-0x8b, size=0x3, align=0
PNP0200: adding io range 0x8f-0x91, size=0x3, align=0
PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0
PNP0200: end config
pnpbios: handle 1 device ID PNP0200 (0002d041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x43, size=0x4, align=0
PNP0100: end config
pnpbios: handle 2 device ID PNP0100 (0001d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x71, size=0x2, align=0
PNP0b00: end config
pnpbios: handle 3 device ID PNP0b00 (000bd041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0
PNP0303: adding io range 0x64-0x64, size=0x1, align=0
PNP0303: end config
pnpbios: handle 4 device ID PNP0303 (0303d041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0
PNP0800: end config
pnpbios: handle 5 device ID PNP0800 (0008d041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0
PNP0c04: end config
pnpbios: handle 6 device ID PNP0c04 (040cd041)
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0xfffe0000-0xffffffff, size=0x20000
PNP0c01: adding fixed memory32 range 0xfec00000-0xfec0ffff, size=0x10000
PNP0c01: adding fixed memory32 range 0xfee00000-0xfee0ffff, size=0x10000
PNP0c01: adding fixed memory32 range 0x100000-0x9ffffff, size=0x9f00000
PNP0c01: end config
pnpbios: handle 7 device ID PNP0c01 (010cd041)
PNP0c02: adding fixed memory32 range 0xf0000-0xf3fff, size=0x4000
PNP0c02: adding fixed memory32 range 0xf4000-0xf7fff, size=0x4000
PNP0c02: adding fixed memory32 range 0xf8000-0xfbfff, size=0x4000
PNP0c02: adding fixed memory32 range 0xfc000-0xfffff, size=0x4000
PNP0c02: end config
pnpbios: handle 8 device ID PNP0c02 (020cd041)
PNP0a03: adding io range 0x4d0-0x4d1, size=0x2, align=0
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0
PNP0a03: adding io range 0x480-0x48f, size=0x10, align=0
PNP0a03: adding io range 0x4000-0x403f, size=0x40, align=0
PNP0a03: adding io range 0x5000-0x501f, size=0x20, align=0
PNP0a03: end config
pnpbios: handle 9 device ID PNP0a03 (030ad041)
PNP0f13: adding irq mask 0x1000
PNP0f13: end config
pnpbios: handle 10 device ID PNP0f13 (130fd041)
PNP0501: adding irq mask 0x10
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0
PNP0501: end config
pnpbios: handle 11 device ID PNP0501 (0105d041)
PNP0700: adding dma mask 0x4
PNP0700: adding io range 0x3f2-0x3f5, size=0x4, align=0
PNP0700: adding irq mask 0x40
PNP0700: end config
pnpbios: handle 12 device ID PNP0700 (0007d041)
PNP0501: adding irq mask 0x8
PNP0501: adding io range 0x2f8-0x2ff, size=0x8, align=0
PNP0501: end config
pnpbios: handle 13 device ID PNP0501 (0105d041)
vt-: vt0 already exists, using vt1 instead
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
isic0 at iomem 0xd0000-0xd0fff irq 9 flags 0x1 on isa0
isic0: passive stack unit 0
isic0: Teles S0/8 (or compatible)
isic0: ISAC 2085 Version V2.3 (B3) (IOM-1)
isic0: HSCX 82525 Version A3
sio0: irq maps: 0x8041 0x8051 0x8041 0x8041
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x8041 0x8049 0x8041 0x8041
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vt0: <pcvt VT220 console driver> at port 0x3b0-0x3df iomem 0xc00b8000-0xc00bffff on isa0
vt0: generic VGA, 80 columns, color, 8 screens, MF2-keyboard
vt1 failed to probe on isa0
isa_probe_children: probing PnP devices
unknown: <PNP0303> can't assign resources
unknown: <PNP0303> at port 0x60 on isa0
unknown: <PNP0800> failed to probe at port 0x61 on isa0
unknown: <PNP0f13> failed to probe at irq 12 on isa0
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
unknown: <PNP0700> can't assign resources
unknown: <PNP0700> at port 0x3f2-0x3f5 on isa0
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> at port 0x2f8-0x2ff on isa0
SMP: enabled INTs: 1, 3, 4, 6, 9, 14, 15, 16, 17, apic_imen: 0xfffc3da5
BIOS Geometries:
 0:03fefe3f 0..1022=1023 cylinders, 0..254=255 heads, 1..63=63 sectors
 0 accounted for
Device configuration finished.
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
i4bctl: ISDN system control port attached
i4btrc: 4 ISDN trace device(s) attached
i4bisppp: 4 ISDN SyncPPP device(s) attached (VJ header compression)
bpf: isp0 attached
bpf: isp1 attached
bpf: isp2 attached
bpf: isp3 attached
i4btel: 2 ISDN telephony interface device(s) attached
i4brbch: 4 raw B channel access device(s) attached
i4b: ISDN call control device attached
bpf: lo0 attached
i4bipr: 4 IP over raw HDLC ISDN device(s) attached (VJ header compression)
bpf: ipr0 attached
bpf: ipr1 attached
bpf: ipr2 attached
bpf: ipr3 attached
ad0: success setting UDMA2 on Intel chip
Creating DISK ad0
ad0: <ST38421A/8.01> ATA-4 disk at ata0-master
ad0: 8056MB (16498944 sectors), 16368 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA33
ad0: piomode=4 dmamode=2 udmamode=4 cblid=1
ata1-master: piomode=3 dmamode=1 udmamode=-1 dmaflag=1
ata1-master: success setting PIO3 on generic chip
acd0: <TOSHIBA CD-ROM XM-5702B/2826> CDROM drive at ata1 as master
acd0: read 2067KB/s (17257KB/s), 256KB buffer, PIO3
acd0: Reads: CD-R, CD-RW, CD-DA
acd0: Writes:
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable trayacd0: Medium: no/blank disc, unlocked
Mounting root from ufs:/dev/ad0s2a
ad0s1: type 0x4, start 63, end = 64259, size 64197 : OK
ad0s2: type 0xa5, start 64260, end = 16498754, size 16434495 : OK
SMP: AP CPU #1 Launched!
SMP: CPU1 apstart_init: trying /sbin/init
c_initialize():
     lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000010 SVR: 0x000001ff