Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.3-STABLE #0: Sat Nov 27 08:38:02 EST 2004 root@mikes-xeon.familysquires.net:/usr/obj/usr/src/sys/XEON Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a31000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0a311f4. Table 'FACP' at 0x1fff3040 Table 'APIC' at 0x1fff6c40 MADT: Found table at 0x1fff6c40 MP Configuration Table version 1.4 found at 0xc00f1400 APIC: Using the MADT enumerator. MADT: Found CPU APIC ID 0 ACPI ID 0: enabled SMP: Added CPU 0 (AP) MADT: Found CPU APIC ID 1 ACPI ID 1: enabled SMP: Added CPU 1 (AP) MADT: Found CPU APIC ID 2 ACPI ID 2: enabled SMP: Added CPU 2 (AP) MADT: Found CPU APIC ID 3 ACPI ID 3: enabled SMP: Added CPU 3 (AP) ACPI APIC Table: Calibrating clock(s) ... i8254 clock: 1193217 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 1784277296 Hz CPU: Intel(R) XEON(TM) CPU 1.80GHz (1784.28-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf24 Stepping = 4 Features=0x3febfbff Hyperthreading: 2 logical CPUs real memory = 536805376 (511 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000000c29000 - 0x000000001f6bffff, 514420736 bytes (125591 pages) avail memory = 515629056 (491 MB) APIC ID: physical 0, logical 0:0 APIC ID: physical 1, logical 0:1 APIC ID: physical 2, logical 0:2 APIC ID: physical 3, logical 0:3 FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 cpu2 (AP): APIC ID: 2 cpu3 (AP): APIC ID: 3 bios32: Found BIOS32 Service Directory header at 0xc00faee0 bios32: Entry = 0xfb370 (c00fb370) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xf0000+0xb3a0 pnpbios: Found PnP BIOS data at 0xc00fbe10 pnpbios: Entry = f0000:be40 Rev = 1.0 Other BIOS signatures found: APIC: CPU 0 has ACPI ID 0 APIC: CPU 1 has ACPI ID 1 APIC: CPU 2 has ACPI ID 2 APIC: CPU 3 has ACPI ID 3 MADT: Found IO APIC ID 4, Interrupt 0 at 0xfec00000 ioapic0: Routing external 8259A's -> intpin 0 ioapic0: intpin 0 -> ExtINT (edge, high) ioapic0: intpin 1 -> ISA IRQ 1 (edge, high) ioapic0: intpin 2 -> ISA IRQ 2 (edge, high) ioapic0: intpin 3 -> ISA IRQ 3 (edge, high) ioapic0: intpin 4 -> ISA IRQ 4 (edge, high) ioapic0: intpin 5 -> ISA IRQ 5 (edge, high) ioapic0: intpin 6 -> ISA IRQ 6 (edge, high) ioapic0: intpin 7 -> ISA IRQ 7 (edge, high) ioapic0: intpin 8 -> ISA IRQ 8 (edge, high) ioapic0: intpin 9 -> ISA IRQ 9 (edge, high) ioapic0: intpin 10 -> ISA IRQ 10 (edge, high) ioapic0: intpin 11 -> ISA IRQ 11 (edge, high) ioapic0: intpin 12 -> ISA IRQ 12 (edge, high) ioapic0: intpin 13 -> ISA IRQ 13 (edge, high) ioapic0: intpin 14 -> ISA IRQ 14 (edge, high) ioapic0: intpin 15 -> ISA IRQ 15 (edge, high) ioapic0: intpin 16 -> PCI IRQ 16 (level, low) ioapic0: intpin 17 -> PCI IRQ 17 (level, low) ioapic0: intpin 18 -> PCI IRQ 18 (level, low) ioapic0: intpin 19 -> PCI IRQ 19 (level, low) ioapic0: intpin 20 -> PCI IRQ 20 (level, low) ioapic0: intpin 21 -> PCI IRQ 21 (level, low) ioapic0: intpin 22 -> PCI IRQ 22 (level, low) ioapic0: intpin 23 -> PCI IRQ 23 (level, low) MADT: intr override: source 0, irq 2 ioapic0: Routing IRQ 0 -> intpin 2 ioapic0: intpin 2 trigger: edge ioapic0: intpin 2 polarity: high MADT: intr override: source 9, irq 9 ioapic0: intpin 9 trigger: level ioapic0: intpin 9 polarity: high ioapic0 irqs 0-23 on motherboard cpu0 BSP: ID: 0x00000000 VER: 0x00050014 LDR: 0x01000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff wlan: <802.11 Link Layer> random: io: mem: Pentium Pro MTRR support enabled null: npx0: [FAST] npx0: on motherboard npx0: INT 16 interface acpi0: on motherboard acpi0: [MPSAFE] pci_open(1): mode 1 addr port (0x0cf8) is 0x80000058 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=25318086) pcibios: BIOS version 2.10 Found $PIR table, 9 entries at 0xc00fded0 PCI-Only Interrupts: 5 9 10 11 Location Bus Device Pin Link IRQs slot 1 0 2 A 0x62 3 4 5 7 9 10 11 12 14 15 slot 1 0 2 B 0x62 3 4 5 7 9 10 11 12 14 15 slot 1 0 2 C 0x62 3 4 5 7 9 10 11 12 14 15 slot 1 0 2 D 0x62 3 4 5 7 9 10 11 12 14 15 slot 2 4 8 A 0x68 3 4 5 7 9 10 11 12 14 15 slot 2 4 8 B 0x69 3 4 5 7 9 10 11 12 14 15 slot 2 4 8 C 0x6a 3 4 5 7 9 10 11 12 14 15 slot 2 4 8 D 0x6b 3 4 5 7 9 10 11 12 14 15 slot 3 4 7 A 0x60 3 4 5 7 9 10 11 12 14 15 slot 3 4 7 B 0x61 3 4 5 7 9 10 11 12 14 15 slot 3 4 7 C 0x62 3 4 5 7 9 10 11 12 14 15 slot 3 4 7 D 0x63 3 4 5 7 9 10 11 12 14 15 slot 4 4 1 A 0x61 3 4 5 7 9 10 11 12 14 15 slot 4 4 1 B 0x62 3 4 5 7 9 10 11 12 14 15 slot 4 4 1 C 0x63 3 4 5 7 9 10 11 12 14 15 slot 4 4 1 D 0x60 3 4 5 7 9 10 11 12 14 15 slot 5 4 2 A 0x62 3 4 5 7 9 10 11 12 14 15 slot 5 4 2 B 0x63 3 4 5 7 9 10 11 12 14 15 slot 5 4 2 C 0x60 3 4 5 7 9 10 11 12 14 15 slot 5 4 2 D 0x61 3 4 5 7 9 10 11 12 14 15 slot 6 4 3 A 0x63 3 4 5 7 9 10 11 12 14 15 slot 6 4 3 B 0x60 3 4 5 7 9 10 11 12 14 15 slot 6 4 3 C 0x61 3 4 5 7 9 10 11 12 14 15 slot 6 4 3 D 0x62 3 4 5 7 9 10 11 12 14 15 slot 7 3 4 A 0x60 3 4 5 7 9 10 11 12 14 15 slot 7 3 4 B 0x61 3 4 5 7 9 10 11 12 14 15 slot 7 3 4 C 0x62 3 4 5 7 9 10 11 12 14 15 slot 7 3 4 D 0x63 3 4 5 7 9 10 11 12 14 15 embedded 0 31 A 0x60 3 4 5 7 9 10 11 12 14 15 embedded 0 31 B 0x61 3 4 5 7 9 10 11 12 14 15 embedded 0 31 C 0x6b 3 4 5 7 9 10 11 12 14 15 embedded 0 31 D 0x63 3 4 5 7 9 10 11 12 14 15 embedded 0 1 A 0x6a 3 4 5 7 9 10 11 12 14 15 embedded 0 1 B 0x6b 3 4 5 7 9 10 11 12 14 15 embedded 0 1 C 0x60 3 4 5 7 9 10 11 12 14 15 embedded 0 1 D 0x61 3 4 5 7 9 10 11 12 14 15 AcpiOsDerivePciId: bus 0 dev 31 func 0 AcpiOsDerivePciId: bus 0 dev 31 func 0 acpi0: Power Button (fixed) ACPI timer: 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 1/0 -> 10 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 unknown: not probed (disabled) cpu0: on acpi0 cpu1: on acpi0 cpu2: on acpi0 cpu3: on acpi0 acpi_tz0: on acpi0 acpi_button0: on acpi0 pcib0: port 0xcf8-0xcff on acpi0 ACPI PCI link initial configuration: pci0: on pcib0 pci0: physical bus=0 map[10]: type 3, range 32, base f0000000, size 25, enabled found-> vendor=0x8086, dev=0x2531, revid=0x04 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0xa090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x2532, revid=0x04 bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x0e (3500 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x2533, revid=0x04 bus=0, slot=2, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x244e, revid=0x04 bus=0, slot=30, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0080, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x2440, revid=0x04 bus=0, slot=31, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 0000f000, size 4, enabled found-> vendor=0x8086, dev=0x244b, revid=0x04 bus=0, slot=31, func=1 class=01-01-80, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 0000d000, size 5, enabled pcib0: matched entry for 0.31.INTD pcib0: slot 31 INTD hardwired to IRQ 19 found-> vendor=0x8086, dev=0x2442, revid=0x04 bus=0, slot=31, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=19 map[20]: type 4, range 32, base 00000500, size 4, enabled pcib0: matched entry for 0.31.INTB pcib0: slot 31 INTB hardwired to IRQ 17 found-> vendor=0x8086, dev=0x2443, revid=0x04 bus=0, slot=31, func=3 class=0c-05-00, hdrtype=0x00, mfdev=0 cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=17 map[20]: type 4, range 32, base 0000d800, size 5, enabled pcib0: matched entry for 0.31.INTC pcib0: slot 31 INTC hardwired to IRQ 23 found-> vendor=0x8086, dev=0x2444, revid=0x04 bus=0, slot=31, func=4 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=23 agp0: mem 0xf0000000-0xf1ffffff at device 0.0 on pci0 agp0: Reserved 0x2000000 bytes for rid 0x10 type 3 at 0xf0000000 agp0: allocating GATT for aperture of size 32M pcib1: at device 1.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0xa000-0xafff pcib1: memory decode 0xf2000000-0xf3ffffff pcib1: prefetched decode 0xe8000000-0xefffffff pci1: on pcib1 pci1: physical bus=1 map[10]: type 3, range 32, base e8000000, size 27, enabled pcib1: device (null) requested decoded memory range 0xe8000000-0xefffffff map[14]: type 4, range 32, base 0000a000, size 8, enabled pcib1: device (null) requested decoded I/O range 0xa000-0xa0ff map[18]: type 1, range 32, base f3000000, size 16, enabled pcib1: device (null) requested decoded memory range 0xf3000000-0xf300ffff pcib0: matched entry for 0.1.INTA pcib0: slot 1 INTA hardwired to IRQ 22 pcib1: slot 0 INTA is routed to irq 22 found-> vendor=0x1002, dev=0x5159, revid=0x00 bus=1, slot=0, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0087, statreg=0x02b0, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) intpin=a, irq=22 powerspec 2 supports D0 D1 D2 D3 current D0 pci1: at device 0.0 (no driver attached) pcib2: at device 2.0 on pci0 pcib2: secondary bus 2 pcib2: subordinate bus 3 pcib2: I/O decode 0xb000-0xbfff pcib2: memory decode 0xf4000000-0xf5ffffff pcib2: prefetched decode 0xfff00000-0xfffff pcib2: could not get PCI interrupt routing table for \\_SB_.PCI0.HUBA - AE_NOT_FOUND pci2: on pcib2 pci2: physical bus=2 found-> vendor=0x8086, dev=0x1360, revid=0x03 bus=2, slot=31, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0020, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x80 (32000 ns) pcib3: at device 31.0 on pci2 pcib3: secondary bus 3 pcib3: subordinate bus 3 pcib3: I/O decode 0xb000-0xbfff pcib3: memory decode 0xf4000000-0xf5ffffff pcib3: prefetched decode 0xfff00000-0xfffff ACPI PCI link initial configuration: pci3: on pcib3 pci3: physical bus=3 map[10]: type 1, range 32, base f5001000, size 12, memory disabled pcib3: device (null) requested decoded memory range 0xf5001000-0xf5001fff pcib2: device (null) requested decoded memory range 0xf5001000-0xf5001fff found-> vendor=0x8086, dev=0x1161, revid=0x01 bus=3, slot=0, func=0 class=08-00-20, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 4, range 32, base 0000b000, size 8, enabled pcib3: device (null) requested decoded I/O range 0xb000-0xb0ff pcib2: device (null) requested decoded I/O range 0xb000-0xb0ff map[14]: type 1, range 64, base f5000000, size 12, enabled pcib3: device (null) requested decoded memory range 0xf5000000-0xf5000fff pcib2: device (null) requested decoded memory range 0xf5000000-0xf5000fff pcib3: matched entry for 3.2.INTA pcib3: slot 2 INTA hardwired to IRQ 18 found-> vendor=0x9005, dev=0x00c0, revid=0x01 bus=3, slot=2, func=0 class=01-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns) intpin=a, irq=18 powerspec 2 supports D0 D3 current D0 map[10]: type 4, range 32, base 0000b400, size 8, enabled pcib3: device (null) requested decoded I/O range 0xb400-0xb4ff pcib2: device (null) requested decoded I/O range 0xb400-0xb4ff map[14]: type 1, range 64, base f5002000, size 12, enabled pcib3: device (null) requested decoded memory range 0xf5002000-0xf5002fff pcib2: device (null) requested decoded memory range 0xf5002000-0xf5002fff pcib3: matched entry for 3.2.INTB pcib3: slot 2 INTB hardwired to IRQ 18 found-> vendor=0x9005, dev=0x00c0, revid=0x01 bus=3, slot=2, func=1 class=01-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns) intpin=b, irq=18 powerspec 2 supports D0 D3 current D0 pci3: at device 0.0 (no driver attached) ahc0: port 0xb000-0xb0ff mem 0xf5000000-0xf5000fff irq 18 at device 2.0 on pci3 ahc0: Defaulting to MEMIO off ahc0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xb000 ahc0: Reading SEEPROM...done. ahc0: Manual SE Termination ahc0: BIOS eeprom is present ahc0: Primary Low Byte termination Enabled ahc0: Primary High Byte termination Enabled ahc0: Downloading Sequencer Program... 423 instructions downloaded ahc0: Features 0x1fef6, Bugs 0x40, Flags 0x28485560 ahc0: [GIANT-LOCKED] aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs ahc1: port 0xb400-0xb4ff mem 0xf5002000-0xf5002fff irq 18 at device 2.1 on pci3 ahc1: Defaulting to MEMIO off ahc1: Reserved 0x100 bytes for rid 0x10 type 4 at 0xb400 ahc1: Reading SEEPROM...done. ahc1: Manual SE Termination ahc1: BIOS eeprom is present ahc1: Primary Low Byte termination Enabled ahc1: Primary High Byte termination Enabled ahc1: Downloading Sequencer Program... 423 instructions downloaded ahc1: Features 0x1fef6, Bugs 0x40, Flags 0x28485560 ahc1: [GIANT-LOCKED] aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs pcib4: at device 30.0 on pci0 pcib4: secondary bus 4 pcib4: subordinate bus 4 pcib4: I/O decode 0xc000-0xcfff pcib4: memory decode 0xf6000000-0xf7ffffff pcib4: prefetched decode 0xfff00000-0xfffff pcib4: Subtractively decoded bridge. ACPI PCI link initial configuration: pci4: on pcib4 pci4: physical bus=4 map[10]: type 1, range 32, base f7100000, size 12, enabled pcib4: device (null) requested decoded memory range 0xf7100000-0xf7100fff map[14]: type 4, range 32, base 0000c000, size 6, enabled pcib4: device (null) requested decoded I/O range 0xc000-0xc03f map[18]: type 1, range 32, base f7000000, size 20, enabled pcib4: device (null) requested decoded memory range 0xf7000000-0xf70fffff pcib4: matched entry for 4.4.INTA pcib4: slot 4 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x1229, revid=0x08 bus=4, slot=4, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns) intpin=a, irq=16 powerspec 2 supports D0 D1 D2 D3 current D0 fxp0: port 0xc000-0xc03f mem 0xf7000000-0xf70fffff,0xf7100000-0xf7100fff irq 16 at device 4.0 on pci4 fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xf7100000 fxp0: using memory space register mapping fxp0: PCI IDs: 8086 1229 8086 100c 0008 fxp0: Dynamic Standby mode is disabled miibus0: on fxp0 inphy0: on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: bpf attached fxp0: Ethernet address: 00:30:48:22:d2:7f fxp0: [MPSAFE] isab0: at device 31.0 on pci0 isa0: on isab0 atapci0: port 0xf000-0xf00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xf000 ata0: channel #0 on atapci0 atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata0-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00 ata0: reset tp2 stat0=50 stat1=00 devices=0x1 ata0: [MPSAFE] ata1: channel #1 on atapci0 atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 ata1: reset tp1 mask=03 ostat0=00 ostat1=50 ata1-master: stat=0x00 err=0x00 lsb=0x00 msb=0x00 ata1-slave: stat=0x10 err=0x01 lsb=0x14 msb=0xeb ata1: reset tp2 stat0=00 stat1=10 devices=0x8 ata1: [MPSAFE] uhci0: port 0xd000-0xd01f irq 19 at device 31.2 on pci0 uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xd000 uhci0: [GIANT-LOCKED] usb0: on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered pci0: at device 31.3 (no driver attached) uhci1: port 0xd800-0xd81f irq 23 at device 31.4 on pci0 uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0xd800 uhci1: [GIANT-LOCKED] usb1: on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered fdc0: port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 fdc0: ic_type 90 part_id 80 fdc0: [MPSAFE] fdc0: [FAST] fd0: <1440-KB 3.5" drive> on fdc0 drive 0 sio0: irq maps: 0x4001 0x4011 0x4001 0x4001 sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A sio1: irq maps: 0x4001 0x4009 0x4001 0x4001 sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A unknown: not probed (disabled) unknown: not probed (disabled) ppc0: using extended I/O port range ppc0: ECP SPP ECP+EPP SPP ppc0: port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/9 bytes threshold ppbus0: on ppc0 plip0: on ppbus0 plip0: bpf attached lpt0: on ppbus0 lpt0: Interrupt-driven port ppi0: on ppbus0 psmcpnp0: irq 12 on acpi0 atkbdc0: port 0x64,0x60 irq 1 on acpi0 atkbd0: irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0047 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 atkbd0: [GIANT-LOCKED] psm0: current command byte:0047 psm0: irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons psm0: config:00000000, flags:00000008, packet size:3 psm0: syncmask:c0, syncbits:00 unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it fdc: fdc0 already exists; skipping it ppc: ppc0 already exists; skipping it sio: sio0 already exists; skipping it sio: sio1 already exists; skipping it Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 ex_isa_identify() unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: at iomem 0xcc000-0xcffff,0xc0000-0xcafff on isa0 pmtimer0 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fe0: not probed (disabled) ie0: not probed (disabled) lnc0: not probed (disabled) pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0 pcic1: not probed (disabled) sc0: at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. procfs registered Timecounter "TSC" frequency 1784277296 Hz quality -100 Timecounters tick every 10.000 msec lo0: bpf attached ata0-master: pio=0x0c wdma=0x22 udma=0x46 cable=80pin ata0-master: setting PIO4 on Intel ICH2 chip ata0-master: setting UDMA100 on Intel ICH2 chip ad0: ATA-5 disk at ata0-master ad0: 57259MB (117266688 sectors), 116336 C, 16 H, 63 S, 512 B ad0: 16 secs/int, 1 depth queue, UDMA100 ar: FreeBSD check1 failed ata1-slave: pio=0x0c wdma=0x22 udma=0x42 cable=40pin ata1-slave: setting PIO4 on Intel ICH2 chip ata1-slave: setting UDMA33 on Intel ICH2 chip acd0: CDRW drive at ata1 as slave acd0: read 6890KB/s (6890KB/s) write 2755KB/s (2755KB/s), 8192KB buffer, UDMA33 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet acd0: Writes: CDR, CDRW, test write, burnproof acd0: Audio: play, 2 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: CD-R 120mm data disc Waiting 15 seconds for SCSI devices to settle (noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted. (noperiph:ahc1:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted. GEOM: new disk ad0 [0] f:00 typ:7 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:57351987 [1] f:80 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:57352050 l:59906385 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad0s1, start 32256 length 29364217344 end 29364249599 GEOM: Configure ad0s2, start 29364249600 length 30672069120 end 60036318719 GEOM: Configure ad0s2a, start 0 length 268435456 end 268435455 GEOM: Configure ad0s2b, start 268435456 length 2147483648 end 2415919103 GEOM: Configure ad0s2c, start 0 length 30672069120 end 30672069119 GEOM: Configure ad0s2d, start 2415919104 length 4294967296 end 6710886399 GEOM: Configure ad0s2e, start 6710886400 length 2147483648 end 8858370047 GEOM: Configure ad0s2f, start 8858370048 length 21813699072 end 30672069119 ahc0: Selection Timeout on A:0. 0 SCBs aborted ahc1: Selection Timeout on A:0. 0 SCBs aborted ahc0: Selection Timeout on A:1. 0 SCBs aborted ahc1: Selection Timeout on A:1. 0 SCBs aborted ahc0: Selection Timeout on A:2. 0 SCBs aborted ahc1: Selection Timeout on A:2. 0 SCBs aborted ahc0: Selection Timeout on A:3. 0 SCBs aborted ahc1: Selection Timeout on A:3. 0 SCBs aborted ahc0: Selection Timeout on A:4. 0 SCBs aborted ahc1: Selection Timeout on A:4. 0 SCBs aborted ahc0: Selection Timeout on A:5. 0 SCBs aborted ahc1: Selection Timeout on A:5. 0 SCBs aborted ahc0: Selection Timeout on A:6. 0 SCBs aborted ahc1: Selection Timeout on A:6. 0 SCBs aborted ahc0: Selection Timeout on A:8. 0 SCBs aborted ahc1: Selection Timeout on A:8. 0 SCBs aborted ahc0: Selection Timeout on A:9. 0 SCBs aborted ahc1: Selection Timeout on A:9. 0 SCBs aborted ahc0: Selection Timeout on A:10. 0 SCBs aborted ahc1: Selection Timeout on A:10. 0 SCBs aborted ahc0: Selection Timeout on A:11. 0 SCBs aborted ahc1: Selection Timeout on A:11. 0 SCBs aborted ahc0: Selection Timeout on A:12. 0 SCBs aborted ahc1: Selection Timeout on A:12. 0 SCBs aborted ahc0: Selection Timeout on A:13. 0 SCBs aborted ahc1: Selection Timeout on A:13. 0 SCBs aborted ahc0: Selection Timeout on A:14. 0 SCBs aborted ahc1: Selection Timeout on A:14. 0 SCBs aborted ahc0: Selection Timeout on A:15. 0 SCBs aborted ahc1: Selection Timeout on A:15. 0 SCBs aborted SMP: AP CPU #3 Launched! cpu3 AP: ID: 0x03000000 VER: 0x00050014 LDR: 0x08000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff SMP: AP CPU #2 Launched! cpu2 AP: ID: 0x02000000 VER: 0x00050014 LDR: 0x04000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff SMP: AP CPU #1 Launched! cpu1 AP: ID: 0x01000000 VER: 0x00050014 LDR: 0x02000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff ioapic0: routing intpin 1 (ISA IRQ 1) to cluster 0 ioapic0: routing intpin 3 (ISA IRQ 3) to cluster 0 ioapic0: routing intpin 4 (ISA IRQ 4) to cluster 0 ioapic0: routing intpin 6 (ISA IRQ 6) to cluster 0 ioapic0: routing intpin 7 (ISA IRQ 7) to cluster 0 ioapic0: routing intpin 8 (ISA IRQ 8) to cluster 0 ioapic0: routing intpin 9 (ISA IRQ 9) to cluster 0 ioapic0: routing intpin 12 (ISA IRQ 12) to cluster 0 ioapic0: routing intpin 13 (ISA IRQ 13) to cluster 0 ioapic0: routing intpin 14 (ISA IRQ 14) to cluster 0 ioapic0: routing intpin 15 (ISA IRQ 15) to cluster 0 ioapic0: routing intpin 16 (PCI IRQ 16) to cluster 0 ioapic0: routing intpin 18 (PCI IRQ 18) to cluster 0 ioapic0: routing intpin 19 (PCI IRQ 19) to cluster 0 ioapic0: routing intpin 23 (PCI IRQ 23) to cluster 0 Mounting root from ufs:/dev/ad0s2a start_init: trying /sbin/init splash: image decoder found: daemon_saver