Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.0-RELEASE #4: Tue Feb 3 16:45:33 GMT 2004 xx@xxxxxxxx.xxx:/usr/src/sys/i386/compile/GENERIC-SMP Preloaded elf kernel "/boot/kernel/kernel" at 0xc0686000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc06860a8. Timecounter "i8254" frequency 1193182 Hz CPU: Pentium III/Pentium III Xeon/Celeron (999.67-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x68a Stepping = 10 Features=0x387fbff real memory = 536805376 (511 MB) avail memory = 514449408 (490 MB) Programming 24 pins in IOAPIC #0 IOAPIC #0 intpin 2 -> irq 0 FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000 cpu1 (AP): apic id: 1, version: 0x00040011, at 0xfee00000 io0 (APIC): apic id: 2, version: 0x00178011, at 0xfec00000 Initializing GEOMetry subsystem Pentium Pro MTRR support enabled npx0: on motherboard npx0: INT 16 interface acpi0: on motherboard ACPI-0625: *** Info: GPE Block0 defined as GPE0 to GPE15 Using $PIR table, 11 entries at 0xc00fdc70 acpi0: power button is handled as a fixed feature programming model. Timecounter "ACPI-fast" frequency 3579545 Hz acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0 acpi_cpu0: on acpi0 acpi_cpu1: on acpi0 acpi_button0: on acpi0 pcib0: port 0x5000-0x500f,0x4080-0x40ff,0x4000-0x407f,0xcf8-0xcff on acpi0 pci0: on pcib0 agp0: mem 0xd0000000-0xd3ffffff at device 0.0 on pci0 pcib1: at device 1.0 on pci0 pci1: on pcib1 pci0: at device 6.0 (no driver attached) isab0: at device 7.0 on pci0 isa0: on isab0 atapci0: port 0x9400-0x940f at device 7.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 uhci0: port 0x9800-0x981f irq 5 at device 7.2 on pci0 usb0: on uhci0 usb0: USB revision 1.0 uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: port 0x9c00-0x9c1f irq 5 at device 7.3 on pci0 usb1: on uhci1 usb1: USB revision 1.0 uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered atapci1: port 0xb000-0xb03f,0xac00-0xac03,0xa800-0xa807,0xa400-0xa403,0xa000-0xa007 mem 0xd6200000-0xd621ffff irq 11 at device 12.0 on pci0 ata2: at 0xa000 on atapci1 ata3: at 0xa800 on atapci1 fxp0: port 0xb400-0xb43f mem 0xd6000000-0xd60fffff,0xd6260000-0xd6260fff irq 12 at device 13.0 on pci0 fxp0: Ethernet address 00:e0:81:02:8a:73 inphy0: on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp1: port 0xb800-0xb83f mem 0xd6100000-0xd61fffff,0xd6264000-0xd6264fff irq 10 at device 14.0 on pci0 fxp1: Ethernet address 00:e0:81:02:8a:74 inphy1: on miibus1 inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp2: port 0xbc00-0xbc3f mem 0xd6220000-0xd623ffff,0xd6261000-0xd6261fff irq 12 at device 15.0 on pci0 fxp2: Ethernet address 00:02:b3:2b:d0:6e inphy2: on miibus2 inphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp3: port 0xc000-0xc03f mem 0xd6240000-0xd625ffff,0xd6263000-0xd6263fff irq 10 at device 16.0 on pci0 fxp3: Ethernet address 00:02:b3:2c:00:0d inphy3: on miibus3 inphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fdc0: port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A sio1 port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A ppc0 port 0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode plip0: on ppbus0 lpt0: on ppbus0 lpt0: Interrupt-driven port ppi0: on ppbus0 atkbdc0: port 0x64,0x60 irq 1 on acpi0 atkbd0: flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 orm0: