Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.2-RELEASE #0: Sun Jan 11 04:21:45 GMT 2004 root@wv1u.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a33000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0a33244. Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel Pentium III (736.01-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x683 Stepping = 3 Features=0x387fbff real memory = 536805376 (511 MB) avail memory = 511766528 (488 MB) ACPI APIC Table: FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0 irqs 0-23 on motherboard Pentium Pro MTRR support enabled npx0: [FAST] npx0: on motherboard npx0: INT 16 interface acpi0: on motherboard pcibios: BIOS version 2.10 Using $PIR table, 6 entries at 0xc00f7d50 acpi0: Power Button (fixed) Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 acpi_cpu0: on acpi0 acpi_cpu1: on acpi0 acpi_cpu1: Failed to attach throttling P_CNT acpi_button0: on acpi0 pcib0: port 0xcf8-0xcff on acpi0 pci0: on pcib0 agp0: mem 0xe0000000-0xe7ffffff at device 0.0 on pci0 pcib1: at device 1.0 on pci0 pci1: on pcib1 pcib1: slot 0 INTA is routed to irq 16 pci1: at device 0.0 (no driver attached) isab0: at device 7.0 on pci0 isa0: on isab0 atapci0: port 0xff00-0xff0f at device 7.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] uhci0: port 0xc400-0xc41f irq 16 at device 7.2 on pci0 usb0: on uhci0 usb0: USB revision 1.0 uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered ums0: Microsoft Microsoft IntelliMouse\M-. Optical, rev 1.10/1.08, addr 2, iclass 3/1 ums0: 5 buttons and Z dir. umass0: LEXAR MEDIA JUMPDRIVE, rev 1.10/0.01, addr 3 uhci1: port 0xc800-0xc81f irq 16 at device 7.3 on pci0 usb1: on uhci1 usb1: USB revision 1.0 uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhub1: port error, restarting port 1 uhub1: port error, giving up port 1 uhub1: port error, restarting port 2 uhub1: port error, giving up port 2 pci0: at device 7.4 (no driver attached) atapci1: port 0xcc00-0xcc3f,0xd000-0xd003,0xd400-0xd407,0xd800-0xd803,0xdc00-0xdc07 mem 0xdffe0000-0xdfffffff irq 18 at device 10.0 on pci0 atapci1: [MPSAFE] ata2: at 0xdc00 on atapci1 ata2: [MPSAFE] ata3: at 0xd400 on atapci1 ata3: [MPSAFE] xl0: <3Com 3c900B-TPC Etherlink XL> port 0xc000-0xc07f mem 0xdffcff80-0xdffcffff irq 19 at device 11.0 on pci0 xl0: Ethernet address: 00:50:da:26:78:24 xl0: selecting 10baseT transceiver, half duplex rl0: port 0xbc00-0xbcff mem 0xdffcfe00-0xdffcfeff irq 16 at device 12.0 on pci0 rl0: Ethernet address: 00:e0:29:50:a3:08 miibus0: on rl0 rlphy0: on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto acpi_button1: on acpi0 atkbdc0: port 0x64,0x60 irq 1 on acpi0 atkbd0: flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 orm0: